| Citation ID |
01001A |
| Citaton Type |
Serious |
| Standard Cited |
19100022 A01 |
| Issuance Date |
2015-12-02 |
| Current Penalty |
1000.0 |
| Initial Penalty |
2000.0 |
| Final Order |
2015-12-15 |
| Nr Instances |
1 |
| Nr Exposed |
7 |
| Related Event Code (REC) |
Complaint |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.22(a)(1): All places of employment, passageways, storerooms, and service rooms shall be kept clean and orderly and in a sanitary condition. WORKSHOP: The pump hose, ran from the eastern side to the western side of the workshop was creating a tripping hazard for the employees. ABATED DURING THE INSPECTION. |
|
| Citation ID |
01001B |
| Citaton Type |
Serious |
| Standard Cited |
19100022 A02 |
| Issuance Date |
2015-12-02 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2015-12-15 |
| Nr Instances |
1 |
| Nr Exposed |
7 |
| Related Event Code (REC) |
Complaint |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.22(a)(2): The floor of every workroom shall be maintained in a clean and, so far as possible, a dry condition. Where wet processes are used, drainage shall be maintained, and false floors, platforms, mats, or other dry standing places should be provided where practicable. WORKSHOP: The floor surface, between the trough/grates and the equipment had an accumulation of water due to water over flowing from the drainage trough on the floor. ABATED DURING THE INSPECTION. |
|
| Citation ID |
01002A |
| Citaton Type |
Serious |
| Standard Cited |
19100132 D01 |
| Issuance Date |
2015-12-02 |
| Abatement Due Date |
2016-03-01 |
| Current Penalty |
800.0 |
| Initial Penalty |
1600.0 |
| Final Order |
2015-12-15 |
| Nr Instances |
1 |
| Nr Exposed |
7 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.132(d)(1): The employer shall assess the workplace to determine if hazards are present, or are likely to be present, which necessitate the use of personal protective equipment (PPE). WORKSHOP: The employer had not assessed the workplace to determine the necessitate and appropriate types of personal protective equipment (PPE) for the employees. |
|
| Citation ID |
01002B |
| Citaton Type |
Serious |
| Standard Cited |
19100132 F01 |
| Issuance Date |
2015-12-02 |
| Abatement Due Date |
2016-03-01 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2015-12-15 |
| Nr Instances |
1 |
| Nr Exposed |
7 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.132(f)(1): The employer shall provide training to each employee who is required by this section to use PPE. WORKSHOP: The employees, required to ear PPE were not provided with training and information on the Personal Protective Equipment (PPE) hazard assessment. |
|
| Citation ID |
01003A |
| Citaton Type |
Serious |
| Standard Cited |
19100178 A04 |
| Issuance Date |
2015-12-02 |
| Abatement Due Date |
2016-03-01 |
| Current Penalty |
1000.0 |
| Initial Penalty |
2000.0 |
| Final Order |
2015-12-15 |
| Nr Instances |
1 |
| Nr Exposed |
2 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.178(a)(4): Modifications and additions which affect capacity and safe operation shall not be performed by the customer or user without manufacturers prior written approval. Capacity, operation, and maintenance instruction plates, tags, or decals shall be changed accordingly. WORKSHOP: The placard of the Mitsubishi powered industrial truck (PIT) that was equipped with a non-factory installed front-end attachment was not changed accordingly. |
|
| Citation ID |
01003B |
| Citaton Type |
Serious |
| Standard Cited |
19100178 A05 |
| Issuance Date |
2015-12-02 |
| Abatement Due Date |
2016-03-01 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2015-12-15 |
| Nr Instances |
1 |
| Nr Exposed |
2 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.178(a)(5): If the truck is equipped with front-end attachments other than factory installed attachments, the user shall request that the truck be marked to identify the attachments and show the approximate weight of the truck and attachment combination at maximum elevation with load laterally centered. WORKSHOP: The employer did not request the manufacturer and went through proper steps and procedures prior to operating the Mitsubishi forklift with a non-factory installed front-end attachment. |
|
| Citation ID |
01004 |
| Citaton Type |
Serious |
| Standard Cited |
19100178 L01 I |
| Issuance Date |
2015-12-02 |
| Abatement Due Date |
2016-03-01 |
| Current Penalty |
1100.0 |
| Initial Penalty |
2000.0 |
| Final Order |
2015-12-15 |
| Nr Instances |
1 |
| Nr Exposed |
2 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.178(l)(1)(i): The employer shall ensure that each powered industrial truck operator is competent to operate a powered industrial truck safely, as demonstrated by the successful completion of the training and evaluation specified in this paragraph (l). WORKSHOP: The employer did not ensure through providing successful training and evaluation that the operators are competent to operate the powered industrial truck (PIT) safely at all times. |
|
| Citation ID |
01005A |
| Citaton Type |
Serious |
| Standard Cited |
19100147 C01 |
| Issuance Date |
2015-12-02 |
| Abatement Due Date |
2016-03-01 |
| Current Penalty |
1100.0 |
| Initial Penalty |
2000.0 |
| Final Order |
2015-12-15 |
| Nr Instances |
1 |
| Nr Exposed |
7 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.147(c)(1): Energy control program. The employer shall establish a program consisting of energy control procedures, employee training and periodic inspections to ensure that before any employee performs any servicing or maintenance on a machine or equipment where the unexpected energizing, startup or release of stored energy could occur and cause injury, the machine or equipment shall be isolated from the energy source and rendered inoperative. WORKSHOP: The employer had not established and implemented a site specific hazardous energy control lockout/tagout program consisting of machine specific step-by-step written procedures and employee training for the employees during servicing and maintenance of equipment, such as (but not limited to) polishing machine, CNC, automatic saw. |
|
| Citation ID |
01005B |
| Citaton Type |
Serious |
| Standard Cited |
19100147 C04 I |
| Issuance Date |
2015-12-02 |
| Abatement Due Date |
2016-03-01 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2015-12-15 |
| Nr Instances |
1 |
| Nr Exposed |
1 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.147(c)(4)(i): Procedures shall be developed, documented and utilized for the control of potentially hazardous energy when employees are engaged in the activities covered by this section. WORKSHOP: The employer had not established and implemented step-by-step written energy control procedures in the machine specific for the employees during servicing and maintenance of equipment, such as (but not limited to) the polishing machine, CNC, automatic saw. |
|
| Citation ID |
01005C |
| Citaton Type |
Serious |
| Standard Cited |
19100147 C07 I |
| Issuance Date |
2015-12-02 |
| Abatement Due Date |
2016-03-01 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2015-12-15 |
| Nr Instances |
1 |
| Nr Exposed |
7 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.147(c)(7)(i): The employer shall provide training to ensure that the purpose and function of the energy control program are understood by employees and that the knowledge and skills required for the safe application, usage, and removal of the energy controls are acquired by employees. WORKSHOP: The employees, as affected and other types , were not provided with training and information in the controlling of potentially hazardous and unexpected releases of revised energy sources (lo/to) during servicing and maintenance of equipment, such as (but not limited to) the polishing machine, CNC, automatic saw. |
|
| Citation ID |
01006A |
| Citaton Type |
Serious |
| Standard Cited |
19100305 G01 |
| Issuance Date |
2015-12-02 |
| Current Penalty |
1400.0 |
| Initial Penalty |
2800.0 |
| Final Order |
2015-12-15 |
| Nr Instances |
2 |
| Nr Exposed |
7 |
| Gravity |
10 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.305(g)(1)(iv)(D): Use of flexible cords and cables. Flexible cords and cables shall not be attached to building surfaces: WORKSHOP: 1. The flexible cord of the polishing machine monitor traveled from the wall outlet, wrapped around the electrical piping twice, traveled overhead to another electrical piping and then to the polishing machine monitor. ABATED DURING THE INSPECTION. 2. The orange extension cord, used power the pump traveled from the wall outlet, went through to the floor, looped in front of the polishing machine, wrapped and looped around a work table/leg and then to the pump. ABATED DURING THE INSPECTION |
|
| Citation ID |
01006B |
| Citaton Type |
Serious |
| Standard Cited |
19100305 G02 III |
| Issuance Date |
2015-12-02 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2015-12-15 |
| Nr Instances |
1 |
| Nr Exposed |
7 |
| Gravity |
10 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.305(g)(2)(iii): Flexible cords and cables shall be connected to devices and fittings so that strain relief is provided that will prevent pull from being directly transmitted to joints or terminal screws. WORKSHOP: The outer sheathing of the orange extension cord of the pump was pulled away from the socket. ABATED DURING THE INSPECTION. |
|
| Citation ID |
01007A |
| Citaton Type |
Serious |
| Standard Cited |
19101200 E01 |
| Issuance Date |
2015-12-02 |
| Abatement Due Date |
2016-03-01 |
| Current Penalty |
800.0 |
| Initial Penalty |
1600.0 |
| Final Order |
2015-12-15 |
| Nr Instances |
1 |
| Nr Exposed |
6 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.1200(e)(1): Employers shall develop, implement, and maintain at each workplace, a written hazard communication program which at least describes how the criteria specified in paragraphs (f), (g), and (h) of this section for labels and other forms of warning, safety data sheets, and employee information and training will be met. WORKSHOP: The employer had not established and implemented a written hazard communication program where employees were required to work with chemicals, such as (but not limited to) iron out rust stain remover, and chlorox. |
|
| Citation ID |
01007B |
| Citaton Type |
Serious |
| Standard Cited |
19101200 H01 |
| Issuance Date |
2015-12-02 |
| Abatement Due Date |
2016-03-01 |
| Current Penalty |
0.0 |
| Initial Penalty |
0.0 |
| Final Order |
2015-12-15 |
| Nr Instances |
1 |
| Nr Exposed |
6 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.1200(h)(1): Employers shall provide employees with effective information and training on hazardous chemicals in their work area at the time of their initial assignment, and whenever a new physical or health hazard the employees have not previously been trained about is introduced into their work area. Information and training may be designed to cover categories of hazards (e.g., flammability, carcinogenicity) or specific chemicals. Chemical-specific information must always be available through labels and material safety data sheets. WORKSHOP: The employer had not trained the employees on hazard communication program where employees were required to work with chemicals, such as (but not limited to) iron out rust stain remover, and chlorox. |
|
